Arb 5611210 Manual do Utilizador

08-10-09 Page 1 of 19 3783146 If you have any queries regarding the installation of this product please contact the distributor from whom it wa

08-10-09 Page 10 of 19 3783146 23. Fit 2 x M12 x 1.75 cage nuts into plate and insert into inside RHS chassis rail and align with underside of cha

08-10-09 Page 11 of 19 3783146 29. Slide bar onto rear of chassis leaving enough room to plug main loom into tail light assemblies on either s

08-10-09 Page 12 of 19 3783146 To the RHS of the vehicle, fit 2 x M12 x 1.75 x 50 ( coarse thread ) bolts, spring washer and flat large gold co

08-10-09 Page 13 of 19 3783146 35. . The single cut out packers to the front of the bar. (As viewed from front of vehicle ) When these packers

08-10-09 Page 14 of 19 3783146 FITTING CENTRE COVER PANEL 37. Compile the components as shown - Centre cover panel - 2 x M6 cage nuts - 2 x M6 x

08-10-09 Page 15 of 19 3783146 42. From underneath rear bar pass two M6 x 25 bolts, flat washers and spring washers through the aligned parts an

08-10-09 Page 16 of 19 3783146 48. Using M8 x 20 bolts, flat washers and flange nuts secure end surrounds to braces finger tight. (RHS shown.)

08-10-09 Page 17 of 19 3783146 53. Fit reflector to end of buffer. 54. Fit urethane buffer to top of end surround using M6 nyloc nuts and large bla

08-10-09 Page 18 of 19 3783146 57. Carefully remove backing tape on the rubber strip and fit to step plate working from the centre outwards. Mak

08-10-09 Page 19 of 19 3783146 FITTING TRAILER PLUG AND GOOSENECK 59. Fit trailer plug to recess using M5 pan head screws as shown by arrows. Fo

08-10-09 Page 2 of 19 3783146 USE PART No QTY DESCRIPTION 6821172L 1 Tail Light Assembly – Left Hand Side (LHS) 6821172R 1 Tail Light Assembly –

08-10-09 Page 3 of 19 3783146 3131192L 1 End surround LHS 3131192R 1 End surround RHS 6151083 6 Bolt M8 x 35 6151132 6 Nut M8 flange 4581044

08-10-09 Page 4 of 19 3783146 FITTING TAIL LIGHTS TO BAR 1. Compile components as shown. - Light assembly (LHS shown) - Light cover - 6 x M6 x

08-10-09 Page 5 of 19 3783146 6. Fit M6 cage nuts to light mount cover bracket as shown. 7. Using M6 x 16 bolts and flat washers, fit cover b

08-10-09 Page 6 of 19 3783146 FITTING LOCKING PIN BRACKETS TO BAR 11. Fit locking pin brackets using two M8 x 25 bolts, flat washers and flange nu

08-10-09 Page 7 of 19 3783146 FITTING LOOM TO VEHICLE 14. Fit loom inside rear cross member of vehicle chassis. The plug for connecting the loom

08-10-09 Page 8 of 19 3783146 17. Make sure when plug is connected to vehicle that wire is cable tied well clear of muffler and exhaust componen

08-10-09 Page 9 of 19 3783146 20. With the help of a friend to hold the previously fitted nut plate in the correct position, fit the LHS end sur